LNMP环境下php-fpm启动脚本

编辑/etc/init.d/php-fpm启动脚本，打开之后是乱码，查找原因是拷贝php-fpm启动脚本文件错误。

从同样环境下同样的php版本拷贝php-fpm启动脚本，重新编辑黏贴过来，保存退出后，可以正常加入启动项；有遇到同样情况的朋友可以直接复制脚本，保持与脚本内容的路径一样即可。

php-fpm启动脚本参考如下：

#! /bin/sh### BEGIN INIT INFO# Provides:          php-fpm# Required-Start:    $remote_fs $network# Required-Stop:     $remote_fs $network# Default-Start:     2 3 4 5# Default-Stop:      0 1 6# Short-Description: starts php-fpm# Description:       starts the PHP FastCGI Process Manager daemon### END INIT INFOprefix=/usr/local/phpexec_prefix=${prefix}php_fpm_BIN=${exec_prefix}/sbin/php-fpmphp_fpm_CONF=${prefix}/etc/php-fpm.confphp_fpm_PID=${prefix}/var/run/php-fpm.pidphp_opts="--fpm-config $php_fpm_CONF --pid $php_fpm_PID"wait_for_pid () { try=0 while test $try -lt 35 ; do  case "$1" in   'created')   if [ -f "$2" ] ; then    try=''    break   fi   ;;   'removed')   if [ ! -f "$2" ] ; then    try=''    break   fi   ;;  esac  echo -n .  try=`expr $try + 1`  sleep 1 done}case "$1" in start)  echo -n "Starting php-fpm "  $php_fpm_BIN --daemonize $php_opts  if [ "$?" != 0 ] ; then   echo " failed"   exit 1  fi  wait_for_pid created $php_fpm_PID  if [ -n "$try" ] ; then   echo " failed"   exit 1  else   echo " done"  fi ;; stop)  echo -n "Gracefully shutting down php-fpm "  if [ ! -r $php_fpm_PID ] ; then   echo "warning, no pid file found - php-fpm is not running ?"   exit 1  fi  kill -QUIT `cat $php_fpm_PID`  wait_for_pid removed $php_fpm_PID  if [ -n "$try" ] ; then   echo " failed. Use force-quit"   exit 1  else   echo " done"  fi ;; status)  if [ ! -r $php_fpm_PID ] ; then   echo "php-fpm is stopped"   exit 0  fi  PID=`cat $php_fpm_PID`  if ps -p $PID | grep -q $PID; then   echo "php-fpm (pid $PID) is running..."  else   echo "php-fpm dead but pid file exists"  fi ;; force-quit)  echo -n "Terminating php-fpm "  if [ ! -r $php_fpm_PID ] ; then   echo "warning, no pid file found - php-fpm is not running ?"   exit 1  fi  kill -TERM `cat $php_fpm_PID`  wait_for_pid removed $php_fpm_PID  if [ -n "$try" ] ; then   echo " failed"   exit 1  else   echo " done"  fi ;; restart)  $0 stop  $0 start ;; reload)  echo -n "Reload service php-fpm "  if [ ! -r $php_fpm_PID ] ; then   echo "warning, no pid file found - php-fpm is not running ?"   exit 1  fi  kill -USR2 `cat $php_fpm_PID`  echo " done" ;; *)  echo "Usage: $0 {start|stop|force-quit|restart|reload|status}"  exit 1 ;;esac